Commercial Cleaning – How To Strip And Seal A Floor

[ad_1]

One of the most time consuming and tricky aspects of commercial cleaning, is the task of stripping and sealing a vinyl floor. there are many problems associated with it and if you do not know what you are doing, then the results can be anything but impressive. A decent commercial cleaner that's worth his weight would know how to do a fantastic job when attempting to strip and seal your vinyl or most other types of flooring.

First off, the area needs to be cleared of all furniture and other bits and pieces. Then the area needs to be thoroughly vacuumed as any dust left on the floor will ruin the glass like finish you are hoping to achieve. Most office cleaning companies have all the proper equipment needed to do this properly. Once the are is clean, a mop and bucket should be used to thoroughly wet the area with the stripper in the bucket. the water should always be as hot as possible, not boiling though as that may damage the floor and not to mention the fumes in the steam from the stripper. Once the stripper solution is down, some steel wool should be used around the edges but always wear gloves as the solution can be very caustic. Remove all scuff marks with the steel wool. then run a buffer with the vac off using the correct type of pad depending on how much old polish needs to be removed. Run the buffer length wise and then cross wise to make sure the whole surface area of ​​the floor is covered. Once that's done, use a wet vac to remove the stripper off the floor followed by a clean mop to clean up any streaks and excess stripper.

You should let it dry before giving it a final buff to seal the floor. The Most commercial cleaning companies That the I have ever 's worked with Usually leave That last step out for times sake but the if you do not seal the floor before laying down new polish, the finish wont be color : as good. Once the floor is completely dry, run a vacuum over the area to pick up any loose dust which remains on the floor. Give the floor at least three coats of a suitable polish and wait till the coat is touch dry before applying the next coat. At no time should you buff the polish between coats. Try and allow at least eight to ten hours hardening time before the floor is used. if the polish is too 'soft', then any scratches or scuff marks will become permanent when the polish hardens. this hardening usually takes between 24-48 hours depending on the polish itself.

[ad_2]

Source by Andrew Radics

Carpet Cleaning – Tips on How to Get Your Carpet Spotless Clean

[ad_1]

It is always good to remember that if you want something to be done right, then you have to use the right methods and techniques. The same applies to carpet cleaning too; only if you choose the right method, will you be able to get your carpet or rug spotlessly clean and dust-free.

To make your carpet adorn a brand-new look, it is important to choose a cleaning technique that suits the fabric as well as the type of fibers that are used in your carpet or rug. You can either opt for do-it-yourself methods or seek the help of professional cleaners. While the former is cheap but less efficient, the latter is expensive but promises you a clean and fresh-smelling carpet.

Steam cleaning is the preferred method if your rug or carpet is heavily soiled with dust as well as stains. Only cleaning with steam will give you deep cleaning that will be necessary to take out all the stains. But this method can not be done all by you and requires the hands of an expert carpet technician. Also, you can use steam cleaning for your carpets only once in a year. And remember the golden rule; use steam and not boiling water. The latter will dislodge the glue that binds the carpet fibers together and spoil it irrevocably.

There are many carpet cleaning kits available in the market today. Make sure you get one only after reading the instructions carefully and understanding if it suits your rug type. You need to vacuum clean and rake the carpet first to remove loose dust and dirt before cleaning the carpet with any product. An enzyme-buffer system is used to remove the oily stains and then a non-residue shampoo is used to thoroughly clean the carpet. After shampooing the carpet well, clean it thoroughly with running water and then dry it out. You can either air dry it or vacuum dry it; wait for a day and then vacuum clean the rug once again to ensure that any remaining dust is removed. This method can be used frequently like every three months which will help keep your carpet fresh, clean and stain-free.

An important thing to take care is to regularly vacuum clean your rug every alternate day or at least every week so that dust does not get settled and ruin the carpet. Dry carpet cleaning is another method that you could consider especially during winter when it may take ages to get it dry. The bonnet method is a great technique; in this a cleaning product mixed with carbonated water is sprayed on the carpet and then a buffer is used to brush the rug using a circular motion. This lifts out the dust particles and helps to clean out the rug. The only disadvantage is that this process is quite tedious and tends to take an awful long time to complete. So go ahead and choose your method of choice and keep your carpet clean and fresh always.

[ad_2]

Source by Gary Davies

Small Business Examples For Prospective Entrepreneurs

[ad_1]

The unemployment rates are still high globally, and this means that an awful lot of people have to consider what they can do to make ends meet. There has been a trend of entrepreneurship over the last two years that has been driven by the lack of trust in the corporate world's priorities and a need to improve living standards due to increased costs. There are several options of small business options that are fairly easy to begin with little or no startup capital. Read on to learn what small business options exist for prospective entrepreneurs.

Cleaning Services

Beginning a cleaning serviced can be done fairly easily. If you like to work with your hands and appreciate a varied schedule, then consider this small business opportunity. Buying supplies from your local cleaning supply store can be done for less than $ 100.00 and the only thing left to do now is to get the word out.

Once you have researched the local cleaning rates, you can make up flyers on your computer and have them bulk copied at your local office supply store in bright colors. Hang them on your church billboard, at the local grocery and stores that allow for local advertisements. You may have to take the first few jobs at a slightly lower rate than you want, but once you get some regular clients and referrals, you'll be able to request higher pay.

Virtual Administrative Assistant

Thanks to the web, the ability for people to work from home is recognized by new entrepreneurs every day. If you have basic office skills, like typing, dictation or editing, you can offer your services as a Virtual Administrative Assistant. Check out the rates for this business on sites like Craigslist or iFreelance to see what other people are offering and what they charge based on the job criteria. There is a lot of work to be had in this field, but realize that your business reputation, as it grows, will help you set your own rates.

The you find you a Once direction for your small business , be sure to lands check ( Azan ) Software and Federal Government Regulations and guidelines for your business type and file Accordingly.

[ad_2]

Source by Frank I. Locust

Choosing the Right Squeegee For Your Window Cleaning Job

[ad_1]

If you decide to become a professional window cleaner, you will need to invest in the right equipment. Having top-of-the-line equipment is definitely worth the investment as a professional craftsman of any trade – window cleaning included.

In this article, I will discuss the various squeegees on the market and their proper application. There are many different makes and models of squeegees, each with their own pluses and minuses to take into consideration.

The standard window cleaning for the old-school window cleaner has been a the brass Ettore squeegee. Brass was used because it is rust proof. As squeegees are constantly exposed to water, it was important to have a tool that would not rust.

However, brass is a relatively heavy metal. Later on, the major squeegee manufacturers began making stainless steel handles and channels. Stainless steel is stronger and lighter than the brass and is a definite improvement especially as one gets longer squeegees because the weight starts to add up.

Metal is a very durable material, but it has it's limitations. For one, when it gets really cold outside metal squeegee handles absorb this cold; nothing is worse than having a freezing cold squeegee. To solve this problem and to make squeegees lighter still, the squeegee manufacturers started making the handles out of very tough and lightweight plastics. These new squeegees are lighter and easier to grip.

Another advancement in squeegee technology has been the use of quick release levers. This allows the window cleaner to slide out the channel and change the rubber without the use of tools. Previously, the window cleaner would have to use a screwdriver to loosen the screws in order to do this. As rubber often needs to be changes fairly frequently, this really is a convenient option.

Still another advance in squeegee technology has been the pivoting squeegee. This is very handy for cleaning windows with a pole as it allows the squeegee to pivot. There are a few pivoting squeegees on the market. The most popular are the Unger Swivel Lock, The Ettore Contour Pro Plus, and the Wagtail.

The Wagtail freely swivels back and forth with very little resistance. This is really a great feature if you are very skillful with the pole as it allows the window cleaner to easily fan the window. However, having too much swivel may be too much to handle for the less experienced window cleaner.

The Unger Swivel Lock has the benefit of being able to adjust the level of tension, thereby, giving the window cleaner the level of swivel they want. It can also be locked into whatever angle in desirable. The Swivel Lock comes in two models, one with the standard 40 degree head and one with a zero degree head / I find that the zero degree version is the most versatile as it is easier to perform most pole maneuvers with a zero degree squeegee.

The Ettore Contour Pro Plus is in a class all it's own. It can swivel side-to-side (although not as well as the Swivel Lock or Wagtail) and it can adjust the forward-and-back head angle. So it can be a standard 40 degree squeegee or you can click it into the zero degree position.

Zero degree squeegees are very handy for the window cleaner. It allows them to "close-out" windows with much greater ease (closing out means to go all the way to the edge). This is especially handy for windows with deep mullions or sills. Deeply recessed window may be almost impossible to clean without using a zero degree squeegee. They are also especially helpful for commercial windows with deep ledges.

Another consideration in selecting a squeegee is what size windows you will be using it on. If you plan on cleaning large store front windows, you may want to get a handle that is compatible with wide body aluminum channels. You see, when you want to go over the largest standard size channel (18 inches) you need to get a sturdier channels so that it remains straight and flush. The longer length of 22 "through 40" can more easily bow if not constructed more rigidly. The wide body aluminum channels (ex. Slayer Channels, and Ettore Super System) are very rigid and lighter than stainless steel. This is important, because when you start going above 18 inches you need to have the squeegee be as light as possible.

If you are planning to be a dedicated storefront window cleaner and you want to do large pieces of glass quickly, you may want to check out Sorbo's line of extra large squeegees. Using a 30 "squeegee will make quick work of those extra big car dealership windows!

[ad_2]

Source by Jesse J Green

Diagnosing Repair Parts on the NSS Stallion 8SC Carpet Extractor

[ad_1]

The NSS Stallion 8SC carpet extractor by National Super Service is one of the best carpet extractors sold in the United States. This extractor is easy to use and is extremely portable and lightweight. Over time small issues might arise with this unit and it may need to be repaired. The extractor itself has four likely areas where things could go wrong and parts need to be fixed. It is important to use OEM NSS parts when repairing this extractor to ensure trouble-free use down the road. The four major areas that could go wrong are the vacuum motor, brush motor, pump and brush assembly. NSS parts are readily available through online National Super Service parts dealers and local NSS dealers.

A common problem with this carpet extractor is that the brush bearings tend to go back prematurely. One of the main reasons for this is that some extractors sit for extended periods of time and the bearings start to rust because water was left in the brush assembly and it was not given time to dry out. There are two ways that bearings can be replaced. The first way is to disassemble the main brush remove the bearings, remove the axle, and replace with new NSS bearings. The second and easiest solution to this problem is to purchase a whole new brush assembly which includes the brush, bearings, axle and bearing clips. There are two screws on the outer housing of the brush assembly, remove the screws in the brush should drop from the machine. Remove the belt from the brush and pull the brush away from the machine. To install the new brush wrap the belt around the pulley, but the brush into the machine and screw in the two outside screws. This is an easy fix to the most common problem with Stallion 8SC has. A great way to ensure that bearings within the brush not go bad is to let air circulate around the brush when the machine is not in use. This will prevent the bearings from rusting and seizing up over time.

The next component that is most likely to fail is the brush motor. Before placing the brush motor check to see that the belt is in good condition and has not snapped. Many people assume that the brush motor is bad and do not check the belt first. This NSS belt is extremely inexpensive and easy to replace. On the lower housing of the machine there are screws which need to be removed to access the brush motor and belt. When replacing the belt make sure to check that the brush motor sprints freely and that the pulley on the brush spins freely. A common reason that brush motors go bad is that the bearings on the brush seize up and this will either snap the belt or put an excessive load on the motor causing it to burnout.

When you notice your machine is losing suction it could be that your vacuum motor is starting to wear out. A good thing to do before replacing the vacuum motor is to check all seals especially on the dome and check the dome gasket. Leaks here will cause loss of suction and prevent carpets from being cleaned properly. To access the vacuum motor there are two screws on the back of the unit undo the screws and the top of the unit will flip forward exposing all the internal components. When doing this make sure that the machine is empty in both the solution and recovery tanks. If the machine is not empty water will spill from these tanks onto the floor. To replace the vacuum motor undo the hold down screws and remove the air outlet from the vacuum motor. Repeat the steps to replace the unit.

The last area that can be problematic on the NSS Stallion 8SC is the pump. On the user control panel there is a red button, when pressed this will cause the pump to start and water will be released from the jets on the lower unit. Before replacing the pump check the jets to see if they are clogged. It is common for water not to come out of the unit when these jets are clogged. The easiest way to clean jets is to soak them in a delimer product. Over time calcium from hard water can build up and plug the tiny holes causing them not to release water. After the jets have been soaked do not try to clean the jet holes with anything sharp. The optimal way to clean these jets is to blow compressed air through the top of the jet, this will release debris and free up the whole. If you're jets are clean and there still is no solution coming out of your machine then you might have a bad pump. To replace the pump under the two screws from the back of the machine until the top of the machine forward exposing the internal parts. Remove the pump and replace with a genuine NSS Stallion 8SC pump. It is important to use only National Super Service parts to ensure extra longevity of your machine.

When working on the NSS Stallion 8SC is important that the power cord be unplugged from the wall and that no power is running to the unit. The Stallion 8SC has now been replaced with the Stallion 818 SC. The major difference between these two carpet extractors is that the Stallion 818 SC has a 18 inch cleaning path instead of a 16 inch cleaning path in the older unit. Some parts for the Stallion 818 SC are interchangeable with the older Stallion 8SC but not all. The main part that is not interchangeable is the brush assembly, so when ordering parts it is important that you order the correct part for the correct machine.

[ad_2]

Source by Lee Harris

Roof Cleaning – Making Your Old Roof Look Like New!

[ad_1]

Many Florida residents that have come from the North are surprised by the idea of ​​roof cleaning – and even more surprised by the fact that many communities here in Florida require it. Reasons for cleaning include aesthetics, property values, energy efficiency, and increased longevity of the roof.

Whatever the main reason, if it is going to be done, it is your best interest to know what choices are available to you. A quality roof should last upwards of 30 years if cared for and maintained properly. Unfortunately, many roofs here in Florida (and increasingly throughout the US) are subjected to unnecessary stress while cleaning the greatly reduces the life expectancy of the roof. With repeated roof cleaning comes certain pitfalls that every homeowner, property manager, and professional cleaner should be aware of in order to avoid damage to property, unnecessary repair costs, and the premature replacement of the roof.

WHY HAS THE ROOF TURNED BLACK?

The black streaking typically found on homes in areas where moisture settles on shingles is not caused by mildew or fungus; it's roof algae. 3M scientists have identified the most common form as Gloeocapsa Magma. Algae spores are carried b the wind, which is why so many houses in the neighborhood can end up with this problem. During the last 20 years, this particular algae strain has become hardier and so has been able to migrate to less humid environments than it has in the past. And in areas where it traditionally has been found, the staining is showing up earlier, is more severe and settles on a greater number of roofs.

HOW CAN IT BE CLEANED?

Typical roof cleaning methods involve either pressure cleaning or chemical solutions containing Chlorine Bleach or Sodium Hydroxide. If used properly, these methods will clean the roof with minimal adverse impact – but the effects can be very temporary and will generally have to be repeated every 6-18 months in order to maintain the appearance of the roof.

WHAT IS THE BEST CLEANING METHOD?

Each method has its advantages and disadvantages.

A chlorine and water solution can be used followed by a thorough rinse. Of course, since chlorine can be toxic to people and plants, proper care should be taken to protect employees and the surrounding property from overspray and runoff. The benefits to using chlorine include a much faster cleaning process and minimal rinsing as compared to other methods. This translates into much less wear & tear on the roof – particularly asphalt shingle roofs.

Sodium Hydroxide based cleaners are generally advertised as safer for the landscaping, but sodium hydroxide is caustic, very toxic, and care should also be used to protect employees and surrounding property. Sodium hydroxide is also a very effective degreaser. So high levels of sodium hydroxide in a cleaning product can cause damage to an asphalt shingle roof that can be irreversible. These products generally require much more rinsing than the chlorine method. The rinsing process is not only time consuming, but it can also be potentially damaging to the roof if not done correctly. A quality sodium hydroxide based product should not require any more than 100 psi to effectively rinse an asphalt shingle roof and even then some granule loss should be expected.

Pressure cleaning is an option that should only be used on a concrete, barrel tile, or metal roofs. Pressure cleaning has the advantage of not requiring chemicals, which eliminates some of the cost – in addition to landscaping and chemical exposure concerns. The down side to pressure cleaning is that it is very time consuming and it exerts tremendous force on a surface that is not really designed to handle it. In addition, repeated pressure cleaning can wear away the surface of some tiles that are only covered by a thin layer of coloring. When this happens, the grey concrete color starts to show through and the roof must be stained or painted.

THESE METHODS ARE NOT LONG-TERM SOLUTIONS.

While these methods are relatively safe and effective when done properly, repeated use will lead to premature aging of the roof. The natural erosion that occurs over tie from the basic forces of heat, cold, wind, and rain alone are enough to weaken most roofs to the point where annual inspections and minor repairs are necessary to prevent significant repair costs. But when the roof is repeatedly subjected to high pressure or harsh chemicals, the aging of the roof structure is significantly accelerated. With repeated cleaning, tiles are more likely to shift, slip, or break and asphalt shingles are more likely to become brittle and crack. When this happens, there is a greater likelihood of tearing the roof membrane simply by walking on the roof. Once gaps are created in the roof and subsequent pressure cleaning or chemical cleaning takes place, these gaps provide the water or caustic solutions a path to the roof membrane and increase the chance of costly roof leaks.

WHAT IS THE ALTERNATIVE?

A proper program of preventative maintenance will eliminate the need for future cleaning and the potential for damage that comes along with it. Preventing the recurrence of the algae growth will require a light spray of chlorine and water or an algae prevention product.

Most quality algaecides will last for approximately 6-12 months before reapplication of the product is necessary. Obviously, the longer the time frame, the better your chances are of minimizing and unnecessary damage to the roof. Prevention programs should be done in conjunction with neighbors whenever possible and many can be applied without a need for walking on the roof.

One important mote about algaecides: Algaecide products are regulated at both the state and federal level. Any algaecide product used on a roof requires EPA registration as a pesticide or biocide and approval for use on a roof. Contractors found violating the law in this regard cold find themselves facing fines up to $ 10,000. per occurrence.

[ad_2]

Source by John Browne

Diagnosing Repair Problem Parts On The NSS Pony 20 SCA

[ad_1]

The NSS Pony 20 SCA is the largest walk behind carpet extractor that National Super Service produces. It has a large 20 gallon tank that allows the unit to clean large carpeted areas quickly and efficiently. Overall this is one of the best carpet extractors produced for the janitorial industry. Although this machine is extremely dependable and durable, over time parts can breakdown and it may need to be repaired. The Pony 20 SCA is a simple machine with just five major components that can fail. These components are the gear drive motor, vacuum motor, brush motor, pump and solenoid valve. It is quite simple to diagnose these parts and quickly repair them. When replacing parts on the NSS Pony 20 SCA is important to use OEM National Super Service parts to ensure that the machine runs correctly after repair.

The Pony 20 SCA is a self-drive unit with variable speed that can cover large areas rapidly. The drive system on this unit is powered by a 120 volt gear motor that powers the wheel assembly. The drive motor is connected to the wheel assembly by a chain, if the drive system goes bad and the machine does not move there are four components which could be bad. The first and largest of these components is the gear motor itself, this can be tested by running direct power to the motor to see if it powers up. The second component is the speed control Board which increases or decreases the amount of voltage going to the motor depending on the speed at which the machine needs to run. On the lever assembly there is a dead man's switch which turns the brush motor on and off. Over time switch components can wear down and fail and may need to be replaced. The last component that can fail is the circuit breaker, which over time can wear out and prematurely overload. The circuit breaker is a three amp 120 volt unit that when overloaded will close the circuit to the brush motor. The other reason that this breaker will shutdown is if the brush motor is drawing more than 3 amps, this may be caused by bad bearings on the drive wheel or something caught around the wheel impeding it from going forwards or backwards.

The Pony 20 SCA recovers solution from the carpet by an internal vacuum motor which sucks the water up through the vacuum shoe on the rear of the unit into the recovery tank. If you experience loss of suction it is important to check all seals and gaskets are clean and working condition. One of the main reasons for loss of suction is a damaged dome gasket located on the top of the machine. Any holes and cracks in this dome gasket will cause vacuum leaks and you will experience loss of suction. Before looking at the vacuum motor as a culprit also check the vacuum shoe and vacuum hose on the rear of the machine for any obstructions which may cause decreased suction. There are two main components within the vacuum system. These two components are the vacuum switch and vacuum motor. To find which component has failed use a multi meter to check to see if you are getting 120 volts to the vacuum motor when the switch is on. If you are getting 120 volts to the vacuum motor then the vacuum motor has prematurely gone bad. Other ways to tell if the vacuum motor is failing is to listen for a loud high-pitched squeal or grinding which would come from the motor bearings. On occasion water can get into the vacuum motor from the recovery tank if the machine is not emptied before the water level reaches the float valve. Other ways that water can get into the vacuum motor is excessive foam in the recovery tank from carpet cleaning detergents. One way to deter foam is to use a defoaming agent by adding it into the recovery tank before use. If you are not getting 120 volts to the vacuum motor when the switch is turned on, chances are the vacuum switch has failed and will need to be replaced. When replacing the vacuum motor in the Pony 20 SCA it is also important to replace the vacuum motor gasket to ensure a tight seal for optimal performance.

The next component which could fail is the brush motor. The brush motor on the Pony 20 SCA drives a rotating filament brush which is used to agitate the carpet fibers. This increases debris pickup and is optimal for food service areas and locations where dirt and grime are ground into the carpet. The number one reason that the brush motor will fail on this unit is if debris is caught up around the brush, or the bearings in the brush roll go bad. This will cause an excessive load be placed on the motor and it will wear out prematurely. Another components to check if the brush is not rotating is the brush belt, this belt could be slipping on the pulley or could be severed. If the brush is not rotating the three components which could be bad are the brush switch, brush breaker or brush motor. To diagnose these parts take a multi meter and check for voltage coming from the brush switch to the breaker when the switch is turned on. If you are getting voltage to the brush breaker then proceed to the next step. Next check for voltage coming from the brush breaker to the brush motor, if there is no voltage there, then chances are your brush motor has failed. If you are not getting voltage from the brush switch to the brush breaker then replace the pump switch with an OEM NSS switch. If you are not getting voltage from the brush breaker to the motor and getting voltage from the pump switch to the brush breaker then chances are your brush breaker has failed and needs to be replaced. In the system there is also an AC rectifier which converts AC to DC power for the brush motor. If the brush switch, brush breaker and brush motor are all getting power then chances are the rectifier needs to be replaced.

The next internal system that could go bad is the pump system. The pump system sprays cleaning solution onto the carpet. If there is no solution coming out of your machine the first thing to check is jets on the lower end of the unit. There are five Jets on the Pony 20 SCA, these Jets are quick connect jets which when turned will break away from the jet housing. There is no need to unscrew the Jets from the spray bar. If you do need to replace the old jet housings be sure not to over tighten the jets as it will crack the plastic in the spray bar. To clean jets, soak in a delimer solution and then use compressed air to clear the jet nozzles. If the Jets are clean and you are not getting any solution on your carpet there are three components which might have failed. These components include the pump switch, pump or solenoid. To test which component has failed use a multi meter to check voltage between the pump switch and solenoid pump. If you are not reading any voltage from the system then chances are your pump switch has failed and will need to be replaced. If you are getting voltage from the pump switch to the pump then one of two components could be bad. The pump and solenoid are attached together but the solenoid can be removed from the pump. On this unit the pump will run continuously run when the pump switch is engaged. The solenoid will open and close to allow water through the pump and then through the spray bar and jets onto the carpet. If you are getting power to the solenoid and the pump and you are not hearing the pump run continuously than the pump will need to be replaced. If you are getting power to the pump and the pump is running then the solenoid will need to be replaced.

Overall the National Super Service Pony 20 SCA is easy to maintain and repair. There are other mechanical components that may need to be replaced but this article covers the major components that make the machine run. It is important not to touch live wires when diagnosing the machine. For optimal performance and reliability only use National Super Service parts when servicing this unit. NSS parts can be purchased from either a local dealer or online store. Our certified service technicians can assist you in finding the correct part for your floor equipment.

[ad_2]

Source by Lee Harris

7 Sizzling Hot Tips For Getting the Best Movers – Get the Best Price and Free Cleaning Too!

[ad_1]

If you live in California, and you are planning on making the move into your new home, then you have found the holy grail of CA movers tips. I am going to lay out for you the "Must Use" tips in order to make the transition into your dream home as smooth as silk. On the flip side, if you do not use these, you are probably making the entire project way harder than it needs to be!

Firstly, seek out the best. Decide to take one full hour to do deep research on the web. Go to Google and type in "ca movers". When you have the results in front of you, go one by one through the options, looking thoroughly at their website. Chances are this is a good indication of the quality of their operation, right out of the gate.

Secondly, after you find the best fit for you, go ahead and call the company in order to ask the manager a few simple questions. We want to know what their expectations and standards are. Do they make sure the people that will handle your private goods have "moving manners"? In other words, do they demand that their handlers treat everything with respect.

Next, while on the telephone, be sure to ask if these people offer a "damaged goods" insurance policy, or something like it. If they make a mistake, drop your favorite piece of furniture, and break it, are they going to reimburse you for it? This is so important, and yet just about nobody ever asks for it. And, for your information, MOST California movers should have this.

Fourthly, what are the prices and rates for the move? Do they measure by "project" or by distance, or what? This is where you are going to be happy that you did a lot of background research. Now you are going to quickly find that the California market is significantly higher than surrounding states, but at least you can now shop and compare company against company. Who is the best in this arena? When you have carefully shopped between vendors, you are guaranteeing yourself the absolute best price on the market.

For the fifth tip, it's something strictly limited to California. It's a totally unique facet of the relocation service that was an outgrowth of the real estate bubble, whereby ca movers and companies tried to get a competitive advantage by offering new services. So here it is. Find out if they do any house cleaning? Believe it or not, there are companies that offer a cleaning service for the goods they transfer or for the house they are settling. This can be key, because lots of old things inside your house may requires a good dusting in order to bring them back to life. But again, it may only be California that does this. Let me know what you find!

Sixth tip: Observe the handlers as they move your things. Are they keeping their commitment to treat everything with respect. Never hesitate to tell the manager if they do a good job, or lousy job. They want feedback!

My final tip, is for you to return a testimonial for the company. If you have a good experience, offer to write a nice letter for them. It's something that they'll remember, and should they take it, they may even give you a discount in the future, or offer referral commission for any new business you stimulate.

That's it. Those are the important tips you can adhere to when making the move into your new estate. Best wishes!

[ad_2]

Source by Timothy Donaghue

Why Plumbing Service Matters: Top 5 Reasons

[ad_1]

In the long lengthen part of the history plumbing industry has marked its status as an indispensable part of the society. Unarguably, the contemporary world acknowledges the importance of clean water drainage and circulation system along with secured garbage disposal arrangements as a way of living a healthy life, without worrying about the biological threats.

The services weave a magic for countries across the world by offering handyman and remodeling solutions to make our environment healthy, safe, and sustainable. An ideal plumbing system protects society and neighborhood from numerous hazardous occasions like:

  • Hazards of accumulating wastes through accurate waste management
  • Vulnerabilities of drinking water by developing water supply and safety plans
  • Designing services for single and multistory dwellings
  • Exposures of storm water drainage
  • Prevents water wastage through the installation of reservoirs
  • Management of public as well as domestic water supply systems

Besides, it further encompasses a wide range of solutions like carpentry, fencing, painting, installation of tile floors, repairing damages to drywall, etc. In this article, we attempt to share some of the critical reasons that underpin the importance of hiring plumbing services as a basic necessity for our homes and offices.

Finding the right plumber with appropriate expertise and knowledge to resolve your mission critical tasks on time is unquestionably important. In this light, having a renowned service provider with a team of expert plumbers to come and fix various home or commercial necessities is quite useful. This is because of the fact that these firms have a staff capable of noticing trivial to critical problems in the minimum possible time with their cutting-edge instruments. Other important of reasons of engaging a reputed service provider includes:

Hygiene Concerns – It is a well- known fact that plumbing services harness water to clean our surroundings for better hygiene and health.

Water Conservation – Another underlying principle of plumbing is the dramatic reduction in amount of water depleted via faucets, toilets, and shower heads. Various Eco-friendly plumbing products available in the market today are recognized for saving billions of gallons of water resource.

Better Efficiency – According to a survey conducted by the US, commercial facilities are capable of saving nearly 3 trillion gallons of water annually by partnering with a professional service provider. Besides, most of the latest plumbing products can facilitate drought prone regions to utilize water more diligently.

Comfort – The services act as a refuge to the comforting meals, restorative relaxation, and soothing baths. Besides serving the functional needs, they add beauty to our homes and lives.

100% Guaranteed Customer Satisfaction – These agencies employ a staff of professional handymen with years of knowledge and experience in performing plumbing tasks in minimum possible time.

To conclude, the plumbing industry has become a robust economic engine over a period of time. It not only removes waste and unclean water to safeguard our environment from various communicable diseases but also provides livelihoods and jobs to hundreds of millions of people worldwide.

[ad_2]

Source by Sukhdarshan Kumar

Tips for Cleaning Pavers and Sealing Pavers

[ad_1]

Pavers add to the beauty of your landscape. A well maintained pavement reflects on the beauty of your house. Therefore, it is essential that you maintain it well. Cleaning pavers would be easy once you know about pavers. Choosing wrong cleaning materials and faulty cleaning methods spoil the look of pavements. Therefore it is important that you learn about pavers before venturing into cleaning.

Understand Pavers

Concrete or limestone is generally used in making pavers. Often bricks and natural stones are also used. You should ensure that pavers are sealed as soon as they are laid in your backyard, driveways or patio. If you do not seal it, stains and cracks on the surface of the pavers can damage your pavements soon. Sealing pavers will enhance the color of the pavers giving a new look. Once applied a sealant, the surface will remain stain free and it will also be easy to clean it.

Cleaning of bricks

Bricks absorb oil and stains fast, making your pavement dirty and slippery. High pressure cleaning is not recommended for brick pavers as it can damage the bricks. Always clean it using a low pressure cleaner.

Cleaning concrete pavers

Color pigments are often used in concrete pavers. Rampant usage of chemicals can cause fading or discoloration of the pavers. Consult a professional before start cleaning concrete pavers. After cleaning you can apply a sealant so that the color remains protected for a long time.

Use simple methods

Your job does not end with sealing pavers. You have to clean pavers regularly because damp weather makes pavers absorb moisture from the environment along with dust and can spoil the show of your pavement. So, clean them and mop them regularly. Avoid using any highly concentrated chemicals that damage the environment. Always look for natural formulae for cleaning. You can use a high pressure cleaner and spray the pavers with salt water. For cleaning stains that are lighter, a solution of detergent and warm water would be advisable. However, stains of petrol or oil will not dissolve in water or soap. You can use a commercial product available in the market under the guidance of a professional. Another way of cleaning oil or petrol stains is the use of kitty litter on pavers on the previous night and sweep off the next day.

Use of chemicals

A solution of bleach powder and water in a proportion of 1:10 can also be used for cleaning pavers. Apply the solution over the pavers with a brush and then scrub. Remember that bleach can cause discoloration. Therefore try it on one of the pavers in a corner and see the result before you start cleaning. For removing paint from pavers, paint thinner can be applied on the pavers and then scrape it out with a rag carefully. The most difficult job is to remove rust stains from pavers. When the normal methods do not work, use an appropriate chemical with the help of a professional. After cleaning pavers allow it to dry.

Safety

You should take adequate safety precautions before starting cleaning pavers. Always wear hand gear and safety goggles if you are doing the cleaning yourself using a chemical agent.

[ad_2]

Source by Tex Rowe